Mitsubishi Pajero - the Repair manual and operation
1. Maintenance instruction
2. Maintenance
3. Engines
3.1. Candles
3.2. Check of wires
3.3. System of ignition
3.4. Capital repairs of the engine
3.5. Diesel and turbodiesel engines 2,5 and 2,8 of l
4. Cooling system
5. Lubrication system
6. Power supply system
7. System of release
8. Fuel system
9. Running gear
10. Suspension bracket and steering
11. Brake system
12. Body
13. Electric equipment
14. Electrical circuitries
Программа, программа для
создание рекламных видеороликов
.
3. Engines
3.1. Candles
3.2. Check of wires
3.3. System of ignition
3.3.1. Adjustments
3.3.2. Check of the sensor of rotation of the crankshaft
3.3.3. Coil of ignition and additional resistor
3.3.4. Replacement of details of system of ignition
3.3.5. Installation of ignition
3.3.6. Adjustment of gaps in valves
3.3.7. Adjustment of turns of idling and quality of mix
3.3.8. Adjustment of composition of mix
3.4. Capital repairs of the engine
3.4.1. Engine electric equipment
3.4.2. Ignition distributor
3.4.3. Generator
3.4.4. Battery
3.4.5. Starter
3.4.6. Traction relay of a starter
3.4.7. Sensors
3.4.8. Instructions on service and repair of the engine
3.4.9. Check of a compression in cylinders of engines
3.4.10. Specifications of engines
3.4.11. Removal and installation of the engine
3.4.12. Cover of a head of the block of cylinders
3.4.13. Rollers and yokes
3.4.14. Cooling system thermostat
3.4.15. Inlet collector
3.4.16. Final collector
3.4.17. The integrated collector (the diesel with a turbo-supercharging)
3.4.18. Turbocompressor
3.4.19. Turbocharger
3.4.20. Radiator
3.4.21. Oil cooler
3.4.22. Fan
3.4.23. Pump of cooling liquid
3.4.24. Head of cylinders
3.4.25. Valves and springs
3.4.26. Saddles
3.4.27. Replacement of the directing plugs
3.4.28. Hydropushers
3.4.29. Gear belt and covers
3.4.30. Chain and cover (engine of 2,6 l)
3.4.31. Oil pallet
3.4.32. Oil pump and saylent-rollers (vibroquenchers)
3.4.33. Cam-shafts and support
3.4.34. Check of a condition of a cam-shaft
3.4.35. Pistons and rods
3.4.36. Back epiploon
3.4.37. Radical bearings
3.4.38. Flywheel
3.4.39. Exhaust system
3.5. Diesel and turbodiesel engines 2,5 and 2,8 of l
3.5.1. Removal and installation of the engine
3.5.2. Dismantling of the engine
3.5.3. Pistons and rods
3.5.4. Valves and shaft of yokes
3.5.5. Head of cylinders and valves, shaft of yokes and yoke
3.5.6. Head of cylinders
3.5.7. Check of a compression
3.5.8. Camshaft and gas-distributing mechanism
3.5.9. Gas distribution mechanism drive
3.5.10. Adjustment of gaps of valves
3.5.11. Adjustment of a tension of a gear belt
3.5.12. Removal of the lower protection cover of a gear belt
The full complex of works on check and adjustment of the engine according to specifications is carried out through 48000 km of a run, or each 2 years ( depending on what will come earlier).