1. Disconnect the battery from weight. Merge cooling liquid and disconnect a radiator hose from the thermostat case.

2. Remove the carburetor, having marked all disconnected hoses and wires.

3. Disconnect all vacuum hoses from a collector.

4. Turn off nuts, having greased them with the getting liquid. Displace a collector easy blows and remove.

5. Clear the demountable planes of a collector and a head of cylinders. Check deformation of the planes, if necessary to a proshlifuyta the head plane (having removed it) and replace a collector.

6. Installation is carried out upside-down. Replace laying. Tighten nuts of a collector with m 22 N.' moment.

1. Air offtake

2. Ventilation hose

3. Inlet branch pipe

4. Pipe

5. Cables of control of the gate and kick - down - the mode

6. Throttle branch pipe

7. Laying

8. Hose of ventilation of a case

9. Hose of the amplifier of brakes

10. Vacuum hose

11. Wire

12. Coil

13. Leveling camera

14. Collector

1. Execute a decompression. For this purpose disconnect the socket in a back part of the fuel tank, start the engine and after its stop switch off ignition.

2. Disconnect the battery from weight. Merge cooling liquid and disconnect a radiator hose from the thermostat case.

3. Designate and disconnect all hoses and wires from a collector. Carefully disconnect and muffle fuel pipes.

4. Disconnect a coil wire from the ignition distributor.

5. Remove the leveling camera.

6. Remove the fuel distributor with nozzles.

7. Remove the ignition distributor.

8. Turn off nuts and bolts and remove a collector.

9. Clear the demountable planes of a collector and a head of cylinders.

10. Installation is carried out upside-down. Replace laying of a collector and the leveling camera. Tighten nuts of a collector with m 16 N.' moment, since a nut in a middle part of a collector. Execute necessary adjustments.

1. Filter

2. Carburetor

3. Laying

4. Top hose of a radiator

5. Perepuskna liquid hose

6. Connecting hose

7. Heater hose

8. Hose of the amplifier of brakes

9. Vacuum hose

10. Conditioner temperature sensor wire

11. Temperature sensor wire

12. Wire of the index of temperature

13. Collector

14. Laying

1. Disconnect the battery from weight. Remove the air filter.

2. Merge cooling liquid and disconnect a radiator hose from the thermostat case.

3. Remove the carburetor.

4. Remove a final branch pipe, the thermostat and laying.

5. Remove the secondary air filter and a branch pipe.

6. Remove an oil indicator.

7. Remove the conditioner compressor. Take the unit aside, without disconnecting from the highway, and fix. Remove a compressor arm.

8. Designate and disconnect all hoses and wires from a collector and the thermostat.

Carefully disconnect and muffle fuel pipes. Take aside the conducting and hoses preventing removal of a collector.

9. Remove the recirculation valve.

10. Turn off nuts and remove a collector.

11. Clear the demountable planes of a collector and a head of cylinders. Check deformation of the planes, if necessary to a proshlifuyta the head plane (having removed it) and replace a collector. On a new collector install all sensors and valves.

12. Installation is carried out upside-down. Replace all laying and a sealant. At first tighten collector nuts by hand, and then with m 22 N.' moment, since a nut in a middle part of a collector. Tighten compressor arm bolts with 45 N.' moment of m, the compressor – 24 N. of m, the thermostat – 12 N. of m. Check operation of all sensors and control lamps for dashboards.

1. Air offtake

2. Bolts of adjustment of a cable of an accelerator

3. Gate cable

4. Accelerator cable

5, 8. Vacuum hose

6. Hose of the amplifier of brakes

7. Recirculation valve temperature sensor socket

9. Recirculation tube bolts

10, 16, 20, 22. Laying

11. Coil wire

12. Coil

13. Arm of a jellied mouth

14. Ventilation hose

15. throttle branch pipe

17, 18. Bolts and nuts

19. Leveling camera

21. Recirculation valve

23, 24. Racks

N – the details which are subject to replacement at assembly

1. Fuel pipe of high pressure

2. Return fuel pipe

3. Vacuum hose

4. Control run socket engine

5. Branch pipe, distributor and regulator of pressure

6. Vacuum distributing

7. Socket of the sensor of the index of temperature of liquid

8. The liquid temperature sensor socket for the conditioner

9. Socket of the sensor of temperature of liquid of a control system of the engine

10. Thermoswitch socket

11. Top hose of a radiator

12. Perepuskna hose

13. Bolts of fastening of a pipe of a heater

14, 16, 18. Laying

15. Collector

17. Final branch pipe

19. Thermostat

20. Conditioner thermoswitch

21. Control system liquid temperature sensor

22. Thermoswitch

23. Sensor of the index of temperature of liquid

24. Thermal valve

1. Cover

2. Switching block

3. Vacuum tube And

4. Vacuum hose And

5. Receiver

6. Absorption valve solenoid

7. Arm

8. A vacuum tube In

9. A vacuum hose In

10. Arm

11, 12, 13. Arms of the leveling camera

14–18. Details of system of recirculation (valve, sensor, tube and laying)

19. Throttle branch pipe

20. Laying

22. Leveling camera

23. Top section

24, 25, 26. Laying

N – the details which are subject to replacement at assembly

1. Wires of nozzles

2. The fuel distributor with nozzles

3, 6. Insulator

4. Pressure regulator

5, 9,12. Ring

7. Bracket

8. Nozzles

10. Sealant

11. Fuel pipe

14. Fuel distributor

15. Collector

16. Sensor of the index of temperature of liquid

17. Control system liquid temperature sensor

18, 19. Hoses

20–22. Final branch pipes

23. Inlet branch pipe

24. Thermostat

25. Case

26. Laying

1. Execute a decompression. For this purpose disconnect the socket in a back part of the fuel tank, start the engine and after its stop switch off ignition.

2. Disconnect the battery from weight. Merge cooling liquid.

3. Disconnect an air duct.

4. Turn off bolts of adjustment of an accelerator.

5. Designate and disconnect all available hoses and wires from a collector.

6. Disconnect a coil wire from the ignition distributor.

7. Remove the coil.

8. Remove a throttle branch pipe and take aside (not to disconnect cooling system hoses from a branch pipe). Remember an arrangement of bolts of fastening of a branch pipe.

Remove laying.

9. Turn off the top bolts of racks, bolts of fastening of the leveling camera and remove the camera and laying.

10. Remove racks.

11. Disconnect both fuel pipes and vacuum hoses, remove the fuel distributor. Disconnect other hoses to which access became possible (a hose of a radiator, perepuskny a hose and vacuum distributing).

12. Turn off bolts and remove the collector camera with laying.

13. Clear the demountable planes of cameras of a collector and a head of cylinders. Check deformation of the planes if the deviation from the plane exceeds 0,3 mm, then replace a collector and rearrange all sensors and valves on a new collector.

14. Installation is carried out upside-down. Replace all laying (sealant not to grease) and a sealant. Delay all connections the required moments.